The Cotton Line 25 v1.0

FS25 Mods |
The Cotton Line 25 v1.0


The Cotton Line is a complete, southern-built cotton harvest line, from the first pass down the rows to the module headed for the gin. Every machine was built from scratch for this pack, with full animations, working hydraulics, safety decals and vmask wear, and each one is made to work with the others.

Features

  • John Deere 9970 cotton picker with a classic 4-row basket picker, hydrostatic drive, front duals and rear-wheel steer.
  • Split 2-row heads: each half lifts on its own. Left Shift + Z cycles left up, right up, or both down for point rows and short ends. A raised head stops picking.
  • High-dump basket that folds down for the road and tips to dump into a boll buggy or module builder.
  • Spindle water tank behind the cab. It goes down while you pick, and the head will not run dry when the tank is filled at any water point.
  • Folding cab ladder that drops when you step out and flips up beside the handrail when you or a hired helper are running the picker.
  • Detailed cab with working dash, a light bar, CB whips and flag, and spinning PTOs and drums on all four row units.
  • Two designs: Factory, as built, or Used, with sun-faded paint, chalky snouts, worn decals, rusty tips and a few replaced snouts. Used costs less.
  • Advanced Damage System ready: when ADS is installed, the service points and pre-shift inspection points sit in the right places on the machine, and the spindle picking units are included.
  • Southland Super 20 LS boll buggy for running seed cotton from the picker to the module builder.
  • Swing, offset hitch so you can run alongside the picker.
  • Hydraulic packer, Big Lip dump door with rubber curtains, and quad unload chains.
  • Boll-Vac.
  • Crustbuster 114″ pull-type, PTO-driven module builder.
  • Dump seed cotton in from above. The bridge and tamper pack it on a full cycle.
  • At 100% it forms a tarped Bailey Farms cotton module. Open the hydraulic rear gate and drive out to drop it.
  • Waving flag up top.
  • Lizard LM-6 module truck with a patina cab.
  • Slide-and-tilt bed with a chain floor loads and unloads modules on its own.
  • Custom tarped cotton module with the Bailey Farms logo. Built by the module builder, hauled by the module truck, ready for the gin.

Optional: Advanced Damage System (FS25_AdvancedDamageSystem) for full service and inspection support on the 9970.

John Deere 9970 Cotton Picker

  • 250 hp
  • 4-row basket picker
  • Hydrostatic drive
  • Front duals
  • Rear-wheel steer
  • Spindle water tank: 275 gal (1,040 l)

Southland Super 20 LS Boll Buggy

  • Lift & Shift boll buggy
  • Swing, offset hitch
  • Hydraulic packer
  • Quad unload chains

Crustbuster 114″ Module Builder

  • 130 hp needed
  • Pull-type, PTO-driven

Lizard LM-6 Module Truck

  • 350 hp
  • 10-speed manual
  • Hauls one Bailey Farms square module, 2.06 x 2.40 x 9.60 m
  • Hauls up to four round modules

Bailey Farms Cotton Module

  • Custom tarped cotton module
  • Bailey Farms logo

Author: Unknown
Having problems with the mod? Check the comments for possible solutions, and report any new bugs you discover.


Download


Useful Information: How to install FS25 Mods | Farming Simulator 25 FAQ | Farming Simulator 25 News | FS25 System Requirements | Download FS25 Game | Giants Editor FS25 | FS25 Modding Guide | FS25 Cheats | FS25 Guides

Leave a Reply

Your email address will not be published. Required fields are marked *